Ihr Warenkorb ist leer
Ihr Warenkorb ist leer10L0L Golfwagen-Blinker-Kit mit Hupenbremse, Warnblinker, Lichtschalter mit 9-poligem Stecker-Kabelbaum, geeignet für Yamaha, Club Car, EZGO (passend für Eingangsstrom 12 V)
Dusty R
Bewertet in den USA am16. Januar 2024
The headlights, taillights and horn were factory installed so all I needed was the turn signals. This kit fit the bill perfectly. The instructions on removing the dash could be better but once I figured that out, they were clear and easy. Work perfectly.
Jeff Phillips
Bewertet in den USA am14. Dezember 2024
Was looking for a turn signal kit for my golf cart and decided to go with this. Instructions are vague and had to do several modifications to adapt this kit to my cart, but in the end, it's all hooked up and works perfectly! Quite pleased with end result, thank you!!
jpard2357
Bewertet in den USA am18. Juni 2021
This unit is almost plug and play with the "Club Car OEM" light kit harness. The only modifications required were as follows:1.) Remove the two spade connections from the "Club Car OEM" light switch on the dash panel and remove the switch. The 12v supply lead unplugged from this switch will attach to the 12v supply lead going to the brake light switch as there is no power on the 12v supply lead going to the brake pedal well in the floor with the "Club Car OEM" harness.2.) You will notice that the center pin on the "Club Car OEM" nine-pin connector is non-existent. This is the lead for the headlight. Cut the wire going to the center pin on the matching "10LOL" nine-pin connector. Crimp a spade connector on this lead (from the turn signal assembly) and plug in to the remaining lead from the "Club Car OEM" light switch. This will effectively connect your turn signal stalk headlight switch with your existing headlight.3.) Reuse the existing hole in the dash panel (from the discarded factory light switch) to install the hazard flasher switch (you may have to make the hole a bit bigger to accommodate).4.) Remember there is no center pin on the "Club Car OEM" nine-pin connector. As such, the connector will not nicely snap-in to the matching "10LOL" nine-pin connector. However, it will connect. It will just need a wire tie to secure the connection so that it will not inadvertently unplug.Once these four modifications are complete everything should work (with the Club Car OEM lights harness).As a final note, I found the turn signal beep to be annoying. I took the black plastic control box supplied with the 10LOL turn signal assembly apart and placed a piece of tape over the transducer (speaker). This is a simple plastic box that has a snap-in cover.
terry mirenzi
Bewertet in den USA am15. Juni 2021
I bought this unit first because it was open box outside of origanal box everything workrd except the right rear turn signal returned it and bought the the same kit from same vender ( manufactor ) and it worked perfictBefore installing I ohem out all wires in previous installed headlight kit at 9 pin harness to know what the color wires on 9 pin pulg did although the two plugs did not mach color wire to color wire the kit did funsion the way it shouldThe problem with first kit was the controller output at its brown wire to 9 pin plug (this is right rear turn wire ) was a steady 12 volts not intermiten the green wire to right front turn showed a intermitten 12 voltsI should say I also had a reducer and relay operated off of key to power all lights
Kyle Patrick
Bewertet in den USA am8. August 2019
Universal but plugs right into most harnesses with existing 9 pin connector. I searched the internet for a while to find a diagram to match the kit because the turn signal stalk shows a headlight function that does not work out of the box. After finding this diagram you can see that the blue wire in the center of the connector is the +12v output from the stalk to activate the headlights, there is not a pin in the harness for this plug. I clipped the blue wire and ran it through a relay and connected it to the output wire of the headlight switch (brown wire I believe) after eliminating it, and it works like a charm.Also, there are 2 blue wires coming from the stalk that join to form the 1 blue wire my assumption that is if you clip these 2 wires you will find one of them to be a low beam function and the other to be the high beam function but since I only had use for 1 beam pattern I didn't go further into the diagnosis.I was installing a Alpha body and my right rear light had to have the turn signal and brake wires swapped, I'm not sure if this is a fault of this product, or the Alpha wiring harness or just an artifact of combining unlike products, but as this product is universal it did it's job.The horn is VERY loud for a golf cart, I partially covered it with duct tape to quiet it down to a normal sound, its a standard car horn.
Produktempfehlungen
24.98€
11 .99 € 11.99€
30.39€
14 .99 € 14.99€