Ganz 👍

Für hobbyschrauber ok wenn man es nicht so häufig braucht

It got wet and now it's useless. It wasn't very good when I first used it straight from the box

Bei großen Drehmomenten ist das Zeil nicht zu gebrauchen. Der Anschlag biegt sich weg und die Schreibe dreht sich mit.Nur verwendbar wenn man Platz hat und das Anfangsdrehmoment unter 80NM liegt.

Work well job.done

Outil de très mauvaise qualité

Macht was es soll. Einfach zu handhaben.

Je ne vous conseil pas de faire un serrage angulaire avec ce jouet, y a du jeu partout donc impossible d'obtenir un serrage correct

Was soll ich sagen relativ billig gemacht... Nadel ist nicht gerade, ob es funktioniert so wie es soll berichte ich nach der Anwendung.

So I have never used one of these before. Nic the bolt head with a file or use dot of paint when specs call for 90° . I can see this being useful for smaller ° specs as they are harder to SEE accurately. I still nicked my bolts to try this out. The mark on your bolt is still important and will tell you if something went wonky with dial indicator while turning. The clip is useless it appears to screw on but THAT piece is not actually attached to the clip handle-which looks to be designed for wires - has the split end to crimp wires and this is covered in rubber so if you bump it the clip stays where you put it but the piece you screw to the bending arm falls out of the clip! It should be welded to the piece that screws ON - all that hold the arm to the clip is rubber..so not useful.The magnet is firmly attached to the screw on piece however and can be made to work quite well. I used a much stronger magnet at my anchor sites and went magnet to magnet. I Also used the bendy arm to help brace it. Any bump to the arm will throw off the measurement so you need to stay out of the path your tool will take. Hold the tool towards the turn lightly before setting the needle to zero otherwise the play in your tool with throw it off 10° or more. I found this useful to see how far I have turned but still double checked with Mark on the bolt head. It was useful in tight areas where turning more than 30° was impossible so 3x 30° gets you to 90° then double check on your bolt head each time also. I felt like this was good to be able to see while turning how far you've gone. Rather than having to remove the socket to check where the mark is. As long as it stays still , you don't bump it while turning and you set the dial with play removed from tool then it is accurate and removes worry of passing your end point. That said I would never ever rely on a tool like this exclusively- still must mark bolt and have an idea where you are going because any bump to the arm and now you don't know where you are at all. So this does NOT replace marking your bolt heads but used properly it will definitely make your torque to angle turns MORE ACCURATE - especially turns under 90° total. It also allows you to get to your end point in 1-3 increments since you can see how far you are turning each time. Typically you want to turn the full spec° in one go and that's hard to do when you can't see the mark on the bolt. Marking the socket itself is a trick I have used also (leave the socket in place-remove the handle- reattach to turn again when space is limited and using non ratcheting handle) but this proved to be more accurate when used properly- you need to keep an eye on wheather it shifts. For sideways engines the rear head is a pain and this tool is easier to see in a mirror than a mark on your socket. I would buy again but the manufacturer needs to fix the issue with the clip or just get rid of it. The unit I recieved is a magnet only tool because the clip is useless -If you want to use a clip and not a magnet-keep looking! Since it worked and was accurate at a great price I gave it 4 stars. If the clip was functional I'd give it 5. AGAIN I WOULD NEVER USE IT WITHOUT MARKING MY BOLT HEAD AS WELL this is a great visual to see where your at while turning BUT if something moves or gets bumped while turning it WILL throw off the measurement- the mark on your bolt not be effected! I hope this review helps. The tool does not come with instructions. If you've never used one try it out on some random bolt where you can see well. Learn how it works and check out how many degrees of play your tool has. I found I could not detach my handle and position it for a second turn without causing the dial to move- better to reset zero and add up 2 -3 equal turns when space limited.