Ihr Warenkorb ist leer
Ihr Warenkorb ist leerEntwickelt, um Draht, flaches Metall und Rohre in Klemmen, Griffe, Halterungen, Haken, Spulen und mehr zu formen. Macht scharfe Winkelbiegen bis zu 5/16 Zoll. Ø Stange und 1 x 1/8 Zoll Flachmetall* Aus gehärtetem Werkzeugstahl * Montage auf einer Werkbank oder in einem Schraubstock gehalten. Kupferrohrbiege-Anwendung ist nicht geeignet. Lieferumfang: Kreisstifte (3/16,1/4 und 1/2 Zoll). Durchmesser) je 1 Stück: Kreisform (2,5 cm. Durchmesser), Anschlagstift, scharfe Winkelschablone und MessgerätLager-Nr. 173207Modell: MUB-1Verpackungsgröße (cm): 33 x 10 x 10 N.W./G.W. 6,2/3 kg
jerry bennett
Bewertet in den USA am30. August 2023
This worked great for bending spoons and other small pieces of metal. Very well constructed.
MirthCastle
Bewertet in den USA am10. Mai 2023
Since this is my first metal bender I wasn't sure what to expect.... After using it to bend some 3/8 rods for some hooks (25 of them) I could tell where the 'cheapness' bled through.TL:DR:This is cheaply made and will not make acurrate multiple bends because the handle pin is loosely fitted.First: The bending pin on the handle doesnt seat all the way, so ends up at a 30-ish degree angle, this makes making multiple bends on the same rod VERY difficult because the travel UP it and not against it, and I found myself using a vise and a hammer to straighten things out. To combat this I would have to constantly rotate the rod with one hand as I rotated the handle to bend it with the other... Though this was by eye, it at least got the parts closer so I could follow up with my vise and hammer.Second: The threads on the knob used to clamp the piece in place warped the very first time, and I can barely turn it without struggling to clamp further pieces... Considering I formed 25 rods, each one with 5 separate bends... I eventually had to use vice grips just to turn the handle to tighten and loosen it.I'm 250lbs, I am trying not to assume anything or take jabs at anyone... but if I struggled... Both with the bending and the weak pin, as well as the knob... I can't imagine someone smaller having an easier time.I DO NOT RECOMMEND this product... Yes I got the job done I was trying to do, but I know that it could have been a lot easier with a better made tool, and so was NOT worth the money.
Brian
Bewertet in den USA am4. Juli 2022
All in all, this is a decent bender. I've use it to make a number or nested bends with stepped diameters, for example, and I found it was fairly straight-forward to make repeatable bends with very little effort.All the components fit as they were intended to fit, and the moving parts move smoothly. The bending bar was a little loose on the pin, but not bad. I suspect some reviewers who complained about the fit may have missed the set screw that anchors the pivot pin. Also, some people complained that the tool came packaged with oil. To me this is a plus. Carb cleaner and a rag takes care of that. (At least it wasn't dry cosmoline).In my case, it would have been nice to have an assortment of additional (larger diameter) spacers, but I believe most people will do just fine with the 4 smaller diameters included.
RedBaron
Bewertet in Großbritannien am 28. November 2021
Having got fed up with my old bender (a cheapie) I splurged on this one thinking it looked a good bit of engineering. Well.....If you do buy it do not even open the box without having to hand:1 quantity of kitchen paper to attempt to de-grease all the parts of the awful lanolin type protection2 a number of Allen keys, not provided (why more than one?? why not settle on one size for the product??)3 some files to work on parts that do not fit (at this price inexcusable - a lazy supplier/manufacturer who cant be bothered to check all fits)4 a lot of patience especially with the instructions that purport to show you how to make a number of complicated things. Would have been much better to show the most efficient way to make one simple bend.After all this my hands, tools and bench covered in lanolin and my mind not in a positive state.So to do todays bending job I used my old bender. A pity I did not check this earlier else I would have returned it for money back.
Bearcat
Bewertet in den USA am31. Januar 2020
I used it to make about 200 eyes in 13 ga hardened wire. Not a finely made bender but it did the job. I may have to put some shims in it next time. BUT it did the job.
Produktempfehlungen
33.89€
15 .99 € 15.99€
70.67€
30 .99 € 30.99€