Perfect oem replacement from Magpul. Personally is way more comfortable than original thin buttpad. Firm, but definitely has some give on the edges overall very happy with it. Does increase length of pull but it's minimal and a non issue to me. Great low cost improvement in my opinion.

Buon prodotto molto valido!

Sono soddisfatto , l'articolo si fissa con molta facilità , consiglio di mettere sulle alettelaterali, un po di olio per farle scivolare meglio nelle sedi,( ho visto che qualche acquirente precedente a avuto problemi), dotato di due viti ma sono uguali come lunghezza a quelle che avevo già. Io personalmente , l'avevo acquistato perché il mio originale mi creava sulla spalla delle micro lesioni ai capillari, soprattutto nel allenamento in bianco , anche con questo non ho risolto più di tanto, anche se ammortizza di più, ho aggiunto una striscia adesiva in gomma nera morbida ( ma questo era un mio problema personale) l'articolo ammortizza di più del originale.

Mega schneller Versand+Zustellung, Produkt wie erwartet - gern wieder!

Passt perfekt!!!Dämpft super

Item is what it is, arrived a week prior to expected delivery date, it is a harder rubber but still has more give then original0.30” pads, slapped right onto my ctr with no problems at all, any reviews saying it didn’t fit without modifications has a simple explanation, their buttstock is commercial spec and this pad is only available for mil-spec!

This enhanced buttpad is fantastic, it fixed the slightly short LOP on my favorite stock position.This pad does stop my stock from fully collapsing and locking but will travel about half the distance so overall you gain 3/4 of an inch or so and since the stock wont lock fully closed you loose that click on the stock as well, so overall it adds maybe 2" to your gun, but it is well worth it. (if your buffer tube has a flat rear end your stock will collapse fully with this pad, only the slant back civvie buffers interfere with this pad)The original pad was hard and slippery providing no traction, and very very little recoil reduction if any, with the original pad i could never really find a comfortable shoulder purchase, not a problem i had with the A2 stock. The replacement is "skeletonized" and does provide alot of traction just because of the little bit of give the pad has, I can really lock the gun into place, and do it very quickly, with the original MOE pad i could never seat the rifle comfortably therefore I could never get into shooting position quickly. The Enhanced Butt Pad fixed all of these issues it took literally 1 minute to install and for only $15 it is a must have if you own a MOE stock. worth every penny and fixes my only complaint with the MOE line of stocks,M.O.E STOCK WIGGLE FIX: 10 cents if that, and 2 minutes of time.like i just said the enhanced buttpad fixed my only complaint with the MOE stock, well the wiggle was my first complaint.I fixed that quickly and easily and the stock has no wiggle, well none that matters maybe .5 mil of side to side play, if done right.What you need to do is take the MOE stock figure out with the new buttpad on where your favorite stock position is. mark the buffer tube with a sharpie so you know where your stock ends and your buffer begins at your most used position. this is your tape line. Take gorrila brand duct tape. GORILLA BRAND ONLY its the best tape mil spec might be ok, but gorilla is the best for thickness durability and stickyness.Clean the buffer as best you can just a good wipe down, to get as much oil off, then take a strip of the gorilla tape, about 2-3" long 1/2-3/4 width that it comes off the roll, and then lay it on top of your buffer tube down the length of the tube, ensuring your tape doesnt touch the sharpie line (the end of your stock) then simply slide your stock over the duct tape and the thick gorilla tape will fill the gap between your stock and buffer. you may have to play around with the size of the tape strip, I made mine as tight as possible, sacrificing some adjustment speed.... maybe a full second? for a tight locking stock. you can do whatever you want, and if you keep the tape behind the line of the stock it will last a long time. After you do this if your results are anything like mine your MOE stock will be just as tight and rattle free as its more expensive ( double $$$) locking brother, the CTR stock