Ihr Warenkorb ist leer
Ihr Warenkorb ist leer Please note: This is a barebone only. A system memory, a storage drive and an operating system are needed to complete this system
Model Number: HUNSN RJ35
Chassis: Aluminum with knockout hole, wiring the cables to the external
CPU: Intel Core i3-N305 Processor 6M Cache, up to 3.80 GHz
AES-NI Supported: Yes
Memory: 1 x SO DIMM DDR5 4800 MT/s, up to 32GB
Storage: 1 x M.2 2280 NVME x4 SSD, 1 x M.2 WiFi adaptor board for M.2 2280 NVME x1 SSD / 1 x 2.5 Inch SATA SSD/HDD, 2 choose 1
Network Card: Intel 2.5GbE I226-V, UDE built-in filter connector
I/O Interface: Power ON/OFF, GPIO, Auto Power Key, CLR CMOS, 2 x USB3.0, 6 x USB2.0,
TF Slot for Data Storage/System Boot, HDMI2.1, DP1.4, 4 x LAN, DC_IN
Expansion: 1. M.2 Key-E WiFi slot for NVME SSD, if need to use M.2 WiFi slot, remove the M.2 NVME adapter board.
2.SATA3.0 socket and WiFi socket signal, 2 choose 1, the signal will automatically switch
3.Support to expand 4 x M.2 x1/mSATA/SATA, contact HUNSN to customize
Power: DC100-240V AC/50-60hz, 12V5A
Operating Temperature: -10°c~70°c
Storage Temperature: 0°c~70°c
Relative Humidity: 5%~85% non-condensing
TDP: 15W
Cooling system: Fanless, 80 x 80mm holes, support to add 8010 fan, 2 x small 4pin fan sockets support temperature-control
Size: 145.6 x 135 x 53.6mm
Weight: 1.3kgs
Packing List: HUNSN RJ35 firewall appliance, power supply, power cord, warranty card
Function: Supports hardware auto power on enabled default, network wake-up, system power management, temperature management
System Compatibility: 5.10.x and above core-based freebsd router systems, linux distros, or win.os supported. UEFI support only
Compatibility: firewalls for pfsense plus, opnsense and other popular open-source software solutions
Kvdh
Überprüft in Belgien am 8. Februar 2025
Good
Pl
Bewertet in Deutschland am 24. Februar 2025
When I got this my idea was to have my firewall and some not too demanding internet facing services running on it.I've had this for couple of month now. It's now running Proxmox and OPNSense as firewall/reverse proxy inside of a VM.The hardware it self is fully adequate for the original task however the passive cooling makes it impossible to fully utilize the CPU. Any CPU utilization that averages above 10% will eventually lead to thermal throttling.I now have it stand on top of another machine so the top fans will also act like fans for the mini pc. This keeps the CPU in normal temperatures. However the NVME drive is almost always at toasty 70C.So if you want to fully utilize this mini pc you need to add 1 external fan on top of the case and one internal to keep the NVME cool.Overall It's a very good Mini PC for the money.4 stars because of the inadequate cooling.
SaladKing
Bewertet in Deutschland am 14. Januar 2025
These low powered and passive cooled devices can be turned into a NAS for nvme drives. Just ask the ever friendly HUNSN support to replace the wifi with a riser card to extend 1 nvme to 4 nvme's.This way you can run nvme in raid. I added 32GB ram to each unit so they can spin all VM's the cpu can handle (running 4 in parallel on some)Again, if you have any doubts or question just send a mail to hunsn support and Elena will be happy to assist you
Veins Meine
Bewertet in Deutschland am 8. Dezember 2024
Sehr schön wie beschrieben! Bin begeistert.👍🏽😊
Tim
Bewertet in Deutschland am 7. März 2024
ich möchte Ihnen gerne meine Erfahrungen mit meiner optimalen Firewall/Miniserver-Konfiguration teilen. Ich habe Proxmox mit ZFS auf einer Samsung MVME im RAID 0 installiert. Darüber habe ich Opnsense ebenfalls mit ZFS eingerichtet. Bitte beachten Sie, dass für die PCIE-Passtrough-Funktionalität zur Maximierung der Leistung, wie in meinem Beispiel mit einer 1 GBit/s WAN, einige Anpassungen am Proxmox-Boot-Tool unter ZFS erforderlich sind.Hier sind die Schritte im Detail:1. Öffnen Sie die Datei `/etc/kernel/cmdline` mit dem Befehl `nano /etc/kernel/cmdline`.2. Fügen Sie den folgenden Eintrag hinzu: `root=ZFS=rpool/ROOT/pve-1 boot=zfs intel_iommu=on`.3. Aktualisieren Sie das Proxmox-Boot-Tool mit `proxmox-boot-tool refresh`.Dadurch wird die IOMMU-Funktionalität aktiviert, und Sie können PCIE-Passtrough verwenden, um Ihre Firewall vollständig zu virtualisieren. In meinem Setup habe ich drei Ports an die Firewall durchgereicht und einen für das Management offen gelassen. Zusätzlich habe ich den virtuellen Adapter des Proxmox-Management an die Firewall angeschlossen, um eine Verwaltung meines Hauptnetzwerks zu ermöglichen.Der Kundensupport vom Hersteller selbst ist ebenfalls sehr positiv aufgefallen, sollte es Probleme geben. Lieferzeit war bei mir zirka 2 Wochen.
Le Meur Pierre
Bewertet in Japan am 6. Juli 2024
I have been running proxmox with some virtual machine with it.Did not get any performance issues, everything is silent, Good if you are getting started with home lab.
woelen
Bewertet in den Niederlanden am 2. September 2024
The system is small, but feels very robust. It is heavy for its little size, lots of metal for cooling the box.The system works well with 32 GByte of DDR5-4800 memory (brand: Vengeance) and a Kingston NV2 SSD, 1 TB. I have Ubuntu 22 running on it and it runs flawlessly, out of the box. I did extensive testing, stressing the CPU and memory, and no errors were encountered.When running al low CPU load, the system runs cool (sensors tells that the core temperature of the CPU is around 40 C, on light load it rises to 50 C.When the CPU is stressed strongly (e.g. 6 cores, running at 100%), then the system gets quite hot (core temperature 75 .. 80 C at ambient temperature of 23 C). The outside of the box then also becomes quite hot, so hot that you cannot bear holding it in your bare hands for more than a few seconds.When an old 12 V PC fan is connected to one of the USB ports and put loosely on top of the box, then even under heavy load, the core temperature does not exceed 60 C and the box itself only feels lukewarm. I use it like that. The slowly spinning fan only takes a few tens of mA from the USB and no dust can reach the inside of the system in that way. There are four holes at the bottom of the box, to which an 80 mm fan can be attached, but the disadvantage of that is that dust will be blown inside the box. With the solution I hooked up, no dust gets inside, and this provides really good cooling.
thket
Bewertet in Deutschland am 18. Oktober 2024
Die Appliance läuft prima. Man kann diese als Firewall oder auch als Home Server nutzen. Es lassen sich zwei M2 NVME einbauen, wenn man auf SATA verzichtet. Habe darauf Proxmox installiert und diverse VMs und Container am laufen. Man muss allerdings die Wärmeentwicklung im Auge behalten. Ich kühle die Aplliance passiv mit externen Lüftern.
Kindle-Kunde
Bewertet in Deutschland am 15. März 2024
Zu der Hardware gibt es nicht viel zu sagen, es ist ein n305 Mini pc mit 4 eth ports. Klasse verarbeitet und im Gegensatz zu vielerlei Konkurrenz komplett aus Metall, wie es sein sollte. Support hat meine Anfrage super schnell beantwortet und überzufriedenstellend (ist das ein wort?) bearbeitet, werde definitiv erneut bei diesem Anbieter bestellen.
Luca
Bewertet in Deutschland am 13. Mai 2024
Jemand der sich mit diesem Produkt auseinandersetzt, wird sicherlich wissen wofür es gebraucht bzw. benutzt werden sollte. Dementsprechend spare ich mir den Absatz dazu.Gerät läuft wunderbar, macht was es soll. Einziger, kleiner Minuspunkt: Es wird warm. Sehr warm, so dass 60 Grad am Kühlkörper keine Seltenheit sind - Der Verkäufer hat mir, auf Nachfrage, 2 Lüfterkits geschickt, die aktuell unterwegs sind, da der Lüfter Anschluss des Systems, sagen wir, speziell ist. Damit sollte es dann auch im 24/7 kühl laufen.Ansonsten: 5 Sterne.
Wayne
Bewertet in den USA am8. September 2023
It's a N100; it runs a bit warmer than I thought it would be. It comes loaded with PFSense +. However, it comes pre-loaded in Chinese; and not the easiest to switch. it also has dns defaulting to CHINA. While it does have PFSense + on it, it does not seem to be registered as a PFSense + client. It runs in the 107 degree F to 120 F so far, but I am only running one client behind it right now.I've been working thru the configs for about a week now. I wanted a more complicated and segmented network due to the types of devices on it, so that's my fault, Once I figured out that I could not get rid of the Chinese DNS/language that it would default to upon reset, I reloaded it with OpnSense.. So far, pretty good. In reality, I was trying to shoehorn 5 distinct networks into 3 on the older wifi router; really wanted a bit more, so this is what I'm starting with. In my case, I wanted to segregate home computers, guest wifi, IOT, storage, and work computers onto distinct networks. This will certainly allow that, along with a managed switch. There is a learning curve, and I should just buy a dedicated access point.The unit's construction is pretty dang good. It does come predrilled for wi-fi antennas, but I haven't been able to find a compatible M.2 wifi card that would act as a Access Point. IF I find one, well, there's room for one inside. Overall, I'm fairly happy with the unit. Actually, I haven't been able to find any fault other than the Chinese defaults; I was able to switch it to English, but upon reset, it went back to Chinese defaults.Should I mention again, the build quality is pretty dang good. Heatsinks are quite BEEFY.. N100 is probably overkill, but it's a more modern design than some of the other variants that use older processors and older DDR3, but those actually cost MORE. I chose the 8G model, mainly because I didn't want to wait.
MJ
Bewertet in Schweden am 28. August 2023
Fungerade till det jag skulle använda den till.
Stefan Reichelt
Bewertet in Deutschland am 16. September 2023
Good little machine. Works beautifully as a hypervisor with Proxmox.Future iterations may need better or active cooling by default, though.Especially for the SSDs and if you allow two of them inside. Without proper airflow, they get toasty, even at idle. Not to the point of overheating, but an almost constant 60C is probably not good for long-term durability?If anyone else wants to add a fan, the CPU-FAN or SYS-FAN headers requires some like a "1.25mm Pitch (PicoBlade) size" connector. Haven't tested that yet, still waiting on material.But normal 4pin PWM or even the smaller 4pin GPU connector are too big.Small note about boot up: If no display is connected to the machine, it will beep five times after the normal boot beep. At first I thought something was wrong, but it's just an indication that no display is connected.
Produktempfehlungen
