Ihr Warenkorb ist leer
Ihr Warenkorb ist leer ART DES ARTIKELS:
Motorrad Oberer und Unterer Sturzbügel Motorschutz
Ausstattung:
Motorschutz Kompatibel mit Versys 650 Versys650 2015 2016 2017 2018 2019 2020 2021
Motorschutz Kompatibel mit Versys KLE 650 KLE650 2015 2016 2017 2018 2019 2020 2021
HINWEIS: Bevor Sie bestellen, überprüfen Sie bitte Ihr Motorradmodell und stellen Sie sicher, dass dieser Artikel geeignet ist.
Aus hochwertigem Material hergestellt
Diese Stangen werden vom Rohrstahl im Finish durch gut geschweißte hergestellt
Der Rohrdurchmesser der Stoßfänger ist 25MM, solide und langlebig.
Pulverbeschichtet für Haltbarkeit und ein tolles Aussehen für die kommenden Jahre.
Ein tolles Upgrade vom ursprünglichen Aussehen des Motorrads.
STURDY STRUKTUR UND VOLLSTÄNDIGE FUNKTIONEN
Hochwertige Kollisionsschutzbügel können Fahrer, Kühler, Motorradkörper und Motor vor dem Kontakt mit dem Boden im Falle eines Sturzes oder Rutschens schützen und Schäden an Ihrem Motorrad minimieren.
Bieten überlegene Festigkeit, maximalen und zuverlässigen Schutz wichtiger Motorradteile.
Das werkseitig integrierte Design sorgt für korrekte Passform und einfache Installation.
Keine Notwendigkeit Bohren, Schneiden, Schweißen oder andere Modifikationen. Aber Installation durch Profi wird empfohlen!
Das Paket enthält
1 Set Motorschutz Stoßfänger mit Befestigungsmaterial Zubehör
Mike
Bewertet in den USA am20. Juli 2023
So, these bars offer great protection for spills or drops. However, you'll need to finesse them with a hammer to get the installed. No, don't beat them on to the bike. Rather, you may have to modify the bars themselves.
Joshua scombordi
Bewertet in den USA am11. August 2023
I had to grind on bolt on the left side to clear the fender, additionally the bracket near the forks is tough to get to. It fit well and is as advertised. Might need a belt grinder for that bolt though.
Harry S G
Bewertet in Großbritannien am 23. Dezember 2022
Disappointed.Don’t install the bottom set until you fit the top.Left side (gear shift side) top mount doesn’t line up. Im an engineer but this is total ball ache for this money.Instructions for bottom pair is good but top pair is rubbish.It’s going to take me another half day that I do not have to finish off.
End User
Bewertet in den USA am12. Juni 2022
Be prepaid to spend all day modifying to make it fit right. I knew the instructions were not going to be good so I did my research before putting them on. I took a lot of pictures and intended on making a video for YouTube since I could not find any for the 2021. Unfortunately the right side top hit the turn signal and the left side had close to an inch of clearance. The worst of it all is that you could not bolt the lower rear by the shifter because the bolt hit the shifter shaft and you could not put the shifter back on and rendered it useless. Without the bolt it barely clears. It would require a counter sunk bolt to work. After the vendor reply saying that it fits and most likely would be installation error and subject to a 15% restock fee. I call BS installation is not that hard once you know the order of things. I decided to modify and make fit. After taking it apart and putting the upper right in a vise and bending the mount then reattach it, 5 trips to the hardware store to buy different length bolts and many washers to use as shims I got it to line up properly. I ground the lower right edge that was about a 16th of an inch away from hitting the clutch basket and touched up the paint. Did not want it to go through the clutch basket if it fell over. The mounting bracket metal is very soft and bends easy. Now to the lower left shifter side. I went to the hardware store and got a countersunk bolt and ground the head down intill I had about a 1/8th of an inch bite on my allen wrench. I was able to get it in but not sure how well it will hold up in a crash or fall over since there is only about a 16th of an inch of the top of the bolt holding it tight. If you decide to purchase start on the gear shifter side to see if it clears on your gear shifter. If it works take it off and start with the top and then put the lower sections on last. If crooked I suggest you buy several length longer bolts for the top section to mount to the motor mounts, also several washers to use for shims. You may need to bend the mount a little for it to fit right and get the lower to mount to the motor mount as well with added shims. Good luck and if it fits properly out of the box it should only take about an hour to install If not expect to spend all day and several trips to the hardware store.
Produktempfehlungen
100.29€
46 .99 € 46.99€