Ihr Warenkorb ist leer
Ihr Warenkorb ist leer Der hochwertige Multimount-Halter mit CNC-gefrästem Sicherheitsanschlag lässt sich über zwei Drehpunkte vertikal verstellen. Der Halter besitzt an beiden Einstellschrauben eine V2A Edestahl-Gewindehülse. Die CS-Version hat ein M6 Gewinde.
Technische Daten:
Mit M6 Gewinde zur Befestigung an gewindelosen Gabelkronen
Doppelgelenkverstellung
Edelstahlschrauben
Multimount mit M6-Gewinde zur Montage an gewindelosen Gabelkronen
Nur für Supernova-Frontleuchten
Ideal für V521s, V1260, E3 PRO und E3 PURE 3
Doppelgelenkverstellung und Edelstahlschrauben
Robin M Romano
Bewertet in den USA am30. Oktober 2024
This is what I needed to move my front bicycle light from the handlebar to the lower forks. It is made of metal, so it is good and sturdy. Instead of using the supplied bolt and interlocking screws, I had to use the bolt from my front forks and the nut and bolt from the original handlebar mount. The supplied fork bolt was not long enough and the mounting screws to hold the light were too thick.
Michael Türk
Bewertet in Deutschland am 27. Oktober 2024
Wenn ich längere Zeit über Kopfsteinpflaster fahre, sekt sich meine Fahrradlampe nach unten, obohl ich richtig fest die Schrauben angezogen habe. Ansonsten macht die Halterung einen stabilen und robusten Eindruck. Schade!
Dieter Heising
Bewertet in Deutschland am 26. März 2024
Robuster, massiver Lampenhalter für die Supernova Lampe. Einwandfrei.
OEGINSD
Bewertet in den USA am5. November 2023
I had the original Super Nova Pro headliamp and had to shim the mount with several washers to get it to work. I wasn't able to get any reply from the manufacturer prior to ordering it or through internet searches.
AmazFreddion Kunde
Bewertet in Deutschland am 1. März 2023
Super teil
Nathan VanderVeen
Bewertet in den USA am8. September 2022
Very well made. I have no doubt it will last a long time. I was able to pretty easily make this work for my Niterider light.
Christian Neidhart
Bewertet in Deutschland am 17. Mai 2021
habe mit das Teil für mein R&M Bike geholt um die SN-Lampe höher zu setzen, damit genug Platz für die Tasche bleibt.
a. dooley
Bewertet in den USA am7. März 2015
Works with a B&M Eyc headlight and looks very elegant. It stays where it's aimed. It's hard to even notice when the light is off.I bolted this up to a spare stem-mounted cable hanger for a canti brake. It keeps the light right under the handlebars, out of the way of the clutter of brakes, cables and fenders at the fork crown.
John Duval
Bewertet in den USA am29. September 2012
I purchased this light after searching for a mount that would not vibrate and would allow some flexibility in position.I used this to mount my Edilux light on cyclocross forks with V-style brakes. My fork was threaded on the back and blind on the front. The mount is also threaded. I drilled the fork thru. The sex bolt that passes through the light was a tad larger than the hole in the light so I had to drill. American style bikes are not designed for German style lights, but the effort is worth it.I was concerned that with so many parts it may not be reliable, but i now am confident it will hold without trouble. It was very easy to dial in the exact height and angle. Tighten the screws even a little and the light is absolutely locked in and won't vibrate or move. It clears the rear light output wire on the bottom of the Edilux, leaving a space in the middle for wire run. I did not trust the mount as an electrical ground because of the anodized parts, so I attached the rear light return by pinching it between side plate and the light mounting boss.
Produktempfehlungen
32.45€
15 .99 € 15.99€
39.99€
20 .99 € 20.99€