Easy assembly. It seems to be decent quality. The allen keys are cheap so they will strip before the screws strip so you wont over tighten. Just make sure to add threadlock because its much sturdier. it's the only universal fire extinguisher on amazon. It's a safety product people shouldn't be complaining over $100CAD ($70USD). I don't think it's "too expensive for what it is." I bought a garrison 2.5lb fire extinguisher which comes with a metal bracket. Hopefully I never need to use it.

Für mich ist das ein Top Produkt es tut was es soll und es hällt alles an ort und stelle aber der preis ist dafür ein wenig zu hoch.Ich habe es gekauft wo es stark reduziert war.Aber alles in allem ein sehr gutes produkt

Bon système MAIS ne se monte pas sur toutes les voitures. Par exemple, ne se monte pas sur une Seat Leon Cupra type 5F. Les rails de siège sont trop écartés...

Excellent quality bracket, but will not fit into BMW i3 as the carpet is higher than the bracket when fitted at a higher point with the grub screwsI tried to fit this and wanted it to work but I would have to make holes in the carpet for the screw ends to go fully downAlso the extinguisher mounting bars are not long enough to reach the end of the carpet slopeOther cars may be OK but BMW i3 is not unfortunately

I could make this a pretty complicated and lengthy review, but I"m not going to. I could also talk myself into a less than five star rating, but I didn't see any similar product that would do as well and the end result is excellent, so five stars it is. What I would tell you:1. SECURE MOUNTING REALLY MATTERS. When I finished, I had a 2.5# Amerex Halotron mounted securely under the front of the driver's seat. My install is basically bulletproof, but I had to modify the installation. Secure mounting is very important, more important even than quick access in my opinion. Vehicles are involved in high-G accidents (collisions, rollovers, etc.) far, far more often than vehicle fires. You do NOT want a fire extinguisher becoming a projectile in an accident. Modern vehicles are extremely good at protecting occupants from injury - even a small fire extinguisher flying around could kill someone if there's a head impact. Five stars for secure mounting, no question, though on my 2021 Subaru Outback Touring XT I had to modify the installation (see below).2. HIGH QUALITY MATERIALS/GOOD DESIGN. Five stars here too. At least for a smaller fire extinguisher, this will be bombproof if installed correctly. An extinguisher in the 2.5# range is great. If very securely installed, you might get a 5# extinguisher mounted securely. The materials here are high quality. The various parts of the mount are good steel with what looks like a good quality powder coating. The holes are accurately placed and properly tapped. The fasteners are stainless steel (extra credit for that). Perhaps we should be able to take those things for granted, but there's a lot of garbage on the market. The same goes for the design. It's simple, flexible, strong and secure if properly installed. One area where the flexibility of this design turned out to matter was how the fire extinguisher was spaced horizontally. You can set it up so the head of the unit is either on the inside or outside, and you can move the central part of the mount left or right to clear the seat mounts/rails or to reduce the chances of snagging your feet when you enter or exit. This is a big plus.3. CREATIVITY MAY BE REQUIRED. The two installation methods in the instructions (which I thought were adequately clear and detailed) will probably take care of most vehicles. They weren't going to work securely on my vehicle. The front seat rails are shaped in a way that would make it hard if not impossible to get what I consider an accident-proof installation, and the plastic trim around the seat rails makes the installation more challenging if you don't want to rip out the trim around the seat rails. That would probably be a rational and only minimally visually disruptive choice, but I wanted something a little more polished. What I did is very simple to describe. In real life, working at the front edge/half under the driver's seat slowed things down. Basically, I replaced the set screw that is tightened against the seat rails to clamp the mount with socket-head screws that thread through the existing tapped holes in the clamps into new holes that I drilled and tapped in the inside side of the seat rails. Easy to describe. Properly positioning the holes, drilling them very low on the rails, and driving a tap (M6 x 1.0) to cut threads on the new seat rail holes wound up taking more time than you'd think it should, and getting the side clamp pieces tight against the seat rails when both pieces are threaded requires some care and attention. I'm still giving this five stars here, but if your vehicle is one of probably very few that don't really work easily with the generic installation you'll need to use some ingenuity and care...but the other mounts I looked at didn't look like they were going to allow me to get creative with a secure installation, which is why I'm going with five stars here. If you expect that something like this should fit every vehicle ever made and install securely in five minutes or less, you'd probably give it fewer stars.3. RANDOM NOTES.- Be aware that depending on your installation, there may be seat adjustment issues. I have mine installed almost touching the front/bottom of the driver's seat. I'm tall and the seat is nearly all the way at the back of its adjustment range. So, someone who's short enough (which would be most people) isn't going to be able to adjust the seat to move it forward - without removing the fire extinguisher and mount. And if they do, unless you have a sedan with an enclosed trunk, where are you going to put that missile-fire extinguisher?- The instructions recommend using blue Loctite thread locker (242) or similar. That seems like a good idea. You don't want the various fasteners becoming loose as a result of vibrations.- I spent a fair bit of time retrieving fasteners that I'd dropped...because they rolled under the seat and then into a space below the interior floor pan and the outer floor pan. I could have saved myself a lot of time if I'd stuff a t-shirt or hand towel under the seat to stop that.

A bit tricky for a first timer, as too much tension would make it slip off the seat track since mine are a bit rounded and shallow. Does work even with a smallish fire extinguisher.I'm posting this weeks after driving through various condition.