Ihr Warenkorb ist leer
Ihr Warenkorb ist leer UTG Recon Picatinny 360 TL Zweibein
3 Positionen klappbare Beine und abschließbare Beinverlängerungen mit rutschfesten gummierten Fußpolstern
Höhenverstellbar in der Mitte: 14 - 17,8 cm.
Der fein einstellbare Spannhebel übt die gewünschte Spannung des Zweibeins auf das 360° Schwenk- und 15° vorwärts, rückwärts, links und rechts neigbar.
Picatinny-Halterung mit gerändelter Rändelmutter und Kreuzschraube aus verstärktem Stahl.
Robuste Konstruktion aus Flugzeugaluminium mit mattschwarzer Eloxierung.
Kunde
Bewertet in Deutschland am 29. August 2024
Top für das Geld
Cheryl Hill
Bewertet in Großbritannien am 17. März 2024
Fantastic service fantastic item
Romeo
Bewertet in Italien am 31. Oktober 2023
Ottima alternativa a marchi ben più costosi.A mio avviso qualitativamente anche migliore.
cjaky
Bewertet in den USA am3. November 2023
I have four different brand bipods, including Harris and Caldwell, this one is as good as the Harris and a whole lot better than the Caldwell. I put it on my CZ 457 MTR, works great, very sturdy.
jagudo
Bewertet in Deutschland am 10. Dezember 2023
Die Seitliche Neigung ist nicht einstellbar, auch nicht mit Hilfe von Werkzeug. Das wäre nur mit Gewalt gegangen. Somit ist das für mich Murks. Rückzahlung des Geldes war anstandslos. Da das Teil aus Polen kommt ist das eine sehr teure Rücksendung (16 Euro)auf eigene Kosten, nie wieder.
Wolf
Bewertet in Kanada am 3. März 2022
Awesome design with great futures
Angelo S
Bewertet in den USA am20. September 2022
To start off i bought a returned bipod with all accesories.Mounting:Used the swivel mount but the base that sits on the stock is not flush for a bergara hmr but after tightening with pliers it seems snug.the picatinny mounting also needs pliers since its a circular knob(like the swivel mount). they should have went with a hex nut.Pan and Tilt:Out the box after mounting the rifle was sitting crooked. after inspecting found that there was tilt already in the assembly and was unable to tilt back to 0 degrees. Removed the bipod and used a vise and breaker bar to loosen the 6mm hex screw on the base of bipod. fixed the tilt and tightened the nut back up but not all the way like the factory had it. This fixed the problem some users have of one leg needing to be longer than the other. Marked the 6mm screw and base to check for movement after live fire.(will report back)The lock lever was also very stiff from factory but will loosen up or break in after a few hammer hits both ways. Seems to work perfect now.Play in assembly:the legs do have some play but the majority of it is removed by tightening the adjustment leg wheel on both sides by turning to lock position.checked all the screws and the main leg bolts were installed at about 50 in-lbs of torque and slightly tightened the other 2 different sets of bolts. i know from prior experience from the roll pins utg uses that they probably will walk out of the hole. it utilizes these on the bottom "shoes".The paint is also easily scratchable and from past experience with utg mlok bipod in the rain caused the bolts in the assembly to rust after only the first shoot in rain scenario.Will report back after shooting 300 win mag on a bolt and finish up this review.Update: 131 rounds later and this thing is holding up very well. the tilt feature works perfectly now. id say deffinetly rated for at least 300 win mag. good buy
Produktempfehlungen
